Mercedes TPMS Light On, How to Reset, Programming, Sensor Replacement

Tire Pressure Monitor (TPM) monitors your Mercedes-Benz tire pressure of all four tires and will warn you if any tires have low pressure. Often referred to as TPMS, it has sensors installed at all four tires, and readings from each tire are transmitted to the TPMS control unit. It is important to understand that although TPMS reset and programming are used interchangeably, they are different procedures. Reset or relearn is when you set new pressure on your tires, install a new OEM TPMS sensor, or rotate tires, and the car needs to recognize the new location of the TPMS sensors. TPMS programming requires manual programming before installing a universal TPMS sensor. During programming, the mechanic will copy the ID of the defective TPMS sensor and copy it to the new TPMS sensor. This procedure is also referred to as TPMS cloning.

In this article, we will discuss the following:

How to reset/relearn Mercedes-Benz TPM / TPMS

---

Depending on the Mercedes model, you must try one of the following instructions.

How to reset (program) TPM (TPMS) in most Mercedes-Benz

1. Check the recommended tire pressure on the inside of the fuel door.
2. Access the Service Menu by using the steering wheel buttons.
3. Scroll until you see TIRE PRESSURE.
4. Press OK on the steering wheel.
5. You should see pressure readings from each tire. If the pressure is too low, you will see a warning for that specific tire out of range.
6. If you receive a message, TIRE PRESSURE TO DISPLAY AFTER A FEW MINUTES; drive for several minutes and check the pressure again.
7. Next, use the steering wheel buttons to restart the TPMS.
8. Press OK to confirm.

Correct the tire pressure. Add air to bring the tire pressure within range. You can add air to your Mercedes by going to a service station or you can use a small 12-air compressor gauge to do this at home. We would recommend a portable air compressor such as the HV-35 SuperFlow 12-volt compressor. It has a built-in gauge and can inflate a tire in 3 minutes plus, it’s inexpensive. Click on the provided link to check the price and use reviews on Amazon.

If the instructions above do not work, try the following instructions. 

TPM INSTRUCTIONS 1:

1. Press the forward/back button on the steering wheel until the trip and odometer are displayed.
2. Press UP or DOWN until the tire pressure monitor is shown.
3. Press the PLUS button, TIRE PRESS. MONITOR-ACTIVATED!-PRESS. It may require driving for a few minutes.
4. If REACTIVE-TIRE PRESS. MONITOR appears, then repeat the procedure.
5. If TIRE PRESS.-CHECK TIRES shows tire pressure is too low or too high.

TPM INSTRUCTIONS 2:

• Press the UP/DOWN button on the steering wheel until you see: TIRE PRESSURE MONITOR CONNECTED REACTIVATION.
• Press the + button, TIRE PRES. NOW OK? is shown.
• Press the + button, and TIRE PRESSURE MONITOR REACTIVATED is displayed.

TPMS INSTRUCTIONS 3:

• Press the UP/DOWN button on the steering wheel to select RUN FLAT TIRE INDICATOR ACTIVE. REACTIVATION POSS.
• Press the + button, TIRE PRES. NOW OK? is shown.
• Press the + button, and RUN FLAT INDICATOR REACTIVATED is displayed.

To relearn new sensors, ID’s car must be driven for 10 mins at over 15 mph.

Where to buy inexpensive Mercedes TPMS sensors?

---

If you need a new TPMS Tire Pressure Monitoring Sensor for Mercedes C, CL, CLK, CLS, E, G, GL, and ML, check the following listing on Amazon. You will find aftermarket and genuine MB TPMS sensors. They cost a fraction of the price compared to what you may pay at a dealer and can be installed by most tire shops.

• Genuine Mercedes-Benz Tire Pressure Monitoring System (TPMS) Sensor, Valve
• Schrader Electronics Tire Pressure Monitoring System Sensor A0035400217
• Tire Pressure Monitor Sensor TPMS for MercedesC300 S550 Smart A0035400217 E350 A0009050030

Installing aftermarket TPMS sensors

---

Many universal TPMS sensors can be used on Mercedes-Benz. These are known as cloneable sensors. Typically these sensors require programming, but there are some units such as multi-fit Universal Programmable  System Kit that doesn’t require factory relearn process.

We recommend that every new TPMS sensor be relearned to your vehicle as the manufacturer recommends, whether you are using an aftermarket or genuine OE sensor. Aftermarket sensors may need special programming to install and relearn. This applies to many  “programmable,” “universal,” or “cloneable” sensors.

How to install/retrofit TPMS in Mercedes-Benz cars?

---

It is even possible to install TPMS on your Mercedes-Benz if it doesn’t come with the system installed at the factory. To install the TPMS on your Mercedes, you must first check that you have installed the TPM Control Unit and the receiving module.  If you have the TPMS module installed, you can watch the following video on how to install TPMS in your Mercedes-Benz. You will need four new genuine Mercedes-Benz TPMS monitoring sensors, which you can purchase on Amazon (check price) for much less than the dealer.

Can I install the TPMS sensor and not perform relearning or programming?

---

Yes, if you can clone the ID of the existing TPMS sensor. If you copy the ID of the existing sensor and write it on the new sensor, then you don’t need to carry any programming at the dealer. This is possible with TPMS sensors such as Dorman Multi-fit Universal Tire Pressure Monitoring System Kit. If you look at that link, there is a video on the product description explaining how this works in detail.

What frequency are Mercedes TPMS Sensors?

---

Mercedes TPMS frequency requirements: 315 MHz sensors in the US and 433 MHz in Europe.

What is the expected life of the Mercedes TPMS Sensor?

---

Inside the Mercedes TPMS, you will find a lithium-ion battery. The life span of Mercedes TPMS sensors can vary between 6 to 10 years, in some cases, they can last even longer. Avoid using products such as Fix-a-flat as they will drastically reduce the life of the TPMS sensors.

What is the Best Scanner to Diagnose Problems with my Mercedes-Benz?

The YOUCANIC full system diagnostic scanner is an essential tool for Mercedes-Benz owners and technicians looking to troubleshoot problems with their vehicles. This diagnostic scanner can help diagnose issues with the engine, transmission, brakes, airbag, ABS, steering systems, and more by reading and interpreting fault codes stored in the car’s computer system. With this information, you can make informed decisions about repairs and maintenance, saving time and money.

In addition to diagnosing problems, the YOUCANIC scanner can also reset maintenance reminders and service indicators, ensuring that your vehicle is properly maintained and preventing potential issues from occurring in the future. This feature is especially useful for Mercedes-Benz owners who want to stay on their vehicle’s maintenance schedule without visiting a dealership or a mechanic. Overall, the YOUCANIC full system diagnostic scanner is a valuable tool that can help you keep your Mercedes-Benz running smoothly and reliably for years.